1995 Chevrolet Tahoe Seats

TL* THE CONTACT OWNS A 1995 CHEVROLET TAHOE. THE CONTACT STATED THAT THE CORNER OF THE FRONT DRIVER'S SIDE SEAT BRACKET HAD FRACTURED, WHICH CAUSED THE SEAT TO ROCK AND BECOME UNSTABLE. THE DEALER (GOOD CHEVROLET, 325 SW 12TH ST, RENTON, WA 98057, (425) 336-0640) STATED THAT THERE WAS NO RECALL ON THE VEHICLE. THE MANUFACTURER HAD NOT BEEN CONTACTED. THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED. THE FAILURE MILEAGE WAS UNAVAILABLE.

FRONT LEFT CORNER OF DRIVERS SEAT BROKE LOOSE AND STARTED ROCKING BACK AND FORTH. I WAS SITTING PARKED AND REACHING IN THE BACK SEAT FOR ITEM.

MY FRONT DRIVER SEAT BRACKETS BROKE WHILE DRIVING ON THE HIGHWAY. THE SEAT NOW ROCKS BACK AND FORTH.

THE FRONT SEAT BRACKET ON THE DRIVERS SIDE PULLED THROUGH THE SHEET METAL ON THE LEFT SIDE, CAUSING THE SEAT TO ROCK BACK.

MY DRIVER'S SEAT BRACKET IS BROKEN AND UNSAFE. *KB

THE BRACKET ON MY FRONT SEAT HAS BROKE IT IS UNDERNEATH SEAT AND IS VERY HARD TO GET TO MY SEAT IS ALWAYS MOVING THIS IS NOT SAFE AND I SHOULD NOT HAVE TO PAY FOR IT AND IT IS NOT SAFE. *TR

WHILE REACHING IN THE BACK SEAT FOR SOMETHING THE DRIVER SEAT FRAME BROKE AT THE LEFT FRONT BOLT. *AK

THE DRIVER SIDE SEAT FRAME BROKE.*JB

WHILE TRAVELING ON THE HIGHWAY WITHOUT PRIOR WARNING THE FRONT DRIVER SEAT HIT THE BOTTOM. PLEASE FILL IN ADDITIONAL INFORMATION DEALER IS AWARE OF THE PROBLEM. PH

DRIVER'S SEAT FAILURE ON A 1995 CHEVROLET TAHOE. THE DESIGN OF THE SEAT PLACES THE FRONT LEFT SEAT FASTENER ON A THIN PIECE OF SHEET METAL RATHER THAN ON THE RE-ENFORCED CORNER OF THE SEAT FRAME. IT APPEARS TO BE SOME KIND OF DESIGN ERROR. THE THIN PIECE OF SHEET METAL SPLIT APART, ALLOWING THE FASTENER TO COME FREE, AND THE SEAT THEN ROCKED BACK, ALMOST TOUCHING THE REAR SEAT BEHIND IT; THE DRIVER WAS LEFT LOOKING UP AT A 60 DEGREE ANGLE AT THE INSIDE ROOF OF THE VEHICLE, AND HOLDING ONTO THE STEERING WHEEL FOR SUPPORT. THIS FAILURE OCCURRED IN THE DRIVEWAY AS THE DRIVER WAS BACKING UP. I SHUDDER TO THINK WHAT WOULD HAVE HAPPENED HAD MY WIFE AND TWO CHILDREN BEEN IN THE CAR AND IN TRAFFIC WHEN THIS OCCURRED. GM SHOULD BE FORCED TO FIX THIS, AS IT IS CLEARLY A SAFETY HAZARD TO THE OCCUPANTS OF THE VEHICLE AS WELL AS TO OTHER VEHICLES ON THE ROAD. IN MY CASE, A CALL TO THE LOCAL DEALER GENERATED A "NEVER HEARD OF THAT" RESPONSE; I ULTIMATELY DISASSEMBLED THE SEAT AND HAD MY LOCAL WELDING SHOP STITCH IN A 1/8 INCH PIECE OF STEEL ACROSS THE ENTIRE FRONT OF THE SEAT FRAME STRUCTURE SO THAT THE RE-ENFORCED CORNERS ARE CONNECTED BY MORE THAN THE FLIMSY PIECE OF SHEET STEEL (THIS IS WHAT GM SHOULD HAVE DONE WITH THE ORIGINAL DESIGN OF THIS SEAT). *NLM

WHILE DRIVING THE VEHICLE AND APPLIED GAS THE FRONT DRIVER SEAT ACT LIKE ROCKING CHAIR, MAKING IT UNSAFE TO DRIVE THE VEHICLE. CONSUMER STATES WENT INTO OUR WEB SITE AND FOUND SEVERAL PEOPLE WITH THE SAME PROBLEM. DEALER SAID NOBODY HAS COMPLAINED ON THIS PROBLEM. PLEASE PROVIDE FURTHER INFORMATION. TS

DRIVERS SIDE SEAT BOLT BROKE LOSE, CAUSING DRIVERS SEAT TO BE UNSTABLE, AND ROCK BACK AND FORTH. DEALER HAS BEEN CONTACTED. PLEASE PROVIDE ANY FURTHER INFORMATION.*AK

BOLT CONNECTING DRIVERS SEAT TO POWER ADJUSTABLE SEAT TRACK ASSEMBLY TORE THROUGH THE SHEET METAL ANCHOR PLATE ON THE SEAT CAUSING THE SEAT TO TIP BACKWARDS ABRUPTLY. MY FATHER OWNS AN INDEPENDENT AUTO REPAIR SHOP AND IS AWARE OF THIS SAME PROBLEM ON OTHER CHEVROLET TRUCKS AND SUV'S. I CONTACTED GM'S CUSTOMER SERVICE CENTER TO INQUIRE IF A RECALL OR SERVICE BULLETIN HAD BEEN ISSUED TO ADDRESS THIS APPARENTLY COMMON PROBLEM. I WAS ADVISED GM HAD NOT ISSUED A RECALL NOR A SERVICE BULLETIN AND DID NOT CONSIDER THIS TO BE A COMMON PROBLEM. *TS *NLM ****DIMSII IVOQ ENTRY POSTED AFTER 12-12-02 CUT OVER TO ARTEMIS****760793

CONSUMER STATED THAT HE WAS REAR ENDED WHILE HE STOPPED ON THE TRAFFIC LIGHT AND THE DRIVERS SEAT MOUNTINGS FAILED. *YD

I HAD A 1995 CHEVROLET PICK UP WITH THE EXACT SAME PROBLEM, WHILE BACKING UP, THE DRIVER SEAT BOTTOM BROKE AWAY FROM WHERE IT ATTACHES TO THE SEAT TRACK. I ONLY WEIGH 160 LBS., SO IT ISN'T A WEIGHT OR ABUSE ISSUE. I FEEL CHEVROLET SHOULD HAVE TO PAY FOR THIS THE SECOND TIME AROUND. WHAT WOULD HAVE HAPPENED IF I WERE IN A TRAFFIC SITUATION?. THIS IS DEFINETLY A SAFETY ISSUE, SUDDENLY, YOUR DRIVING FROM THE REAR SEAT LYING ON YOUR BACK!.*AK

HAD SEAT REPAIRED TWICE CAN NOT REPAIR AGAIN SHOULD BE RECALLED. *AK

LOWER SEAT RISER FAILED ON DRIVERS SEAT, DEALER REPLACED WHILE UNDER WARRANTY BUT A FEW HUNDRED MILES LATER SEAT FRAME MADE NOISES AND FOUND FRAME HAD CRACKS IN IT. VEHICLE WAS THEN OUT OF WARRANTY AND DEALER WOULD NOT REPLACE SEAT FRAME. I ALSO KNOW OF ONE OTHER PERSON WHO HAS HAD SAME PROBLEM WITH THEIR TAHOE.

THE SEAT FRAME BROKE WHEN I CAME TO A NORMAL STOP. I TOOK THE VEHICLE TO DIVER CHEV FOR REPAIR. THEY REPLACED THE SEAT FRAME WITH THE PART IN STOCK. THE SEAT NOW IS JAMMED AGAINST THE CONSOLE. I COMPLAINED TO THE SERVICE MANAGER AND HE TOLD ME THAT THIS WAS THE ONLY PART AVAILABLE AND THAT HE HAD NO SOLUTION. I EXPLAINED THAT THE POWER SEAT WAS UNDER CONSTANT STRESS AND IT MAY BE A SAFETY ISSUE IS I WEERE INVILVED IN AN ACCIDENT AS IT COULD BREAK FREE AS IT WAS BASICLY PUSHED OUT OF NORMAL ALIGNMENT. INADDITION THE POWER SEAT MOTOR STRUGGLES TO MOVE THE SEAT WHICH WILL WEAR IT OUT NOT TO MEMTION THAT THE SEAT BOTTOM IS JAMMED AGAIST THE CONSOLE AND IT WILL WEAR THE LEATHER OUT. I CALLED CHEV OWNER ASSISTANCE 1-800-222-1020 AND THEY AGREED THAT THE PROBLEM SHOULD AHVE NEVER OCCURED BUT AFTER CALLING THE DEALER SAID THER WAS NOTHING THEY COULD DO. I FILED A COMPLAINT WITH BBB AUTO LINE AND THEY SENT ME BACK A LETTER AND SAID THE VEHICLE WAS OUT OF WARRANTY AND THEY WOULD NOT PROGRESS THE COMPLAINT. I AM LEFT PAYING $ 268.00 FOR A FAULTY REPAIR WHICH I BELIVE HAS NOW RESULTED IN A POTENTIAL SAFETY ISSUE NOT TO MENTION THE WEAR ISSUES ON THE LEATHER SEAT AND POWER SEAT MOTOR. *AK

THE DESIGN OF THE SEAT MOUNTING IS UNSAFE. THE SEAT IS MOUNTED TO A WEAK CROSS BRACE INSTEAD OF THE MAIN SEAT FRAME RAILS. THIS DESIGN IS DOOMED TO REPEATED FAILURES AND IS UNSAFE. IF THE SEAT WAS MOUNTED BY THE MAIN FRAME RAILS THERE WOULD BE NO PROBLEMS. CHEVROLET SHOULD REDESIGN THE SLIDE BRACKET TO MOUNT TO THE PROPER MOUNTING POINTS.*AK

NO SUMMARY LISTED FOR ABOVE VEHICLE. *AK

FRONT POWER ADJUSTING SEAT MOUNT BROKE OFF STEEL. PIECE OF STEEL INSUFFICIENT/ TOO SMALL / THIN, AND WEAK TO HOLD SEAT PROPERLY, CAUSING LOSS OF PROTECTION.*AK

WHILE TRAVLING DRIVER WAS ADJUSTING SEAT, AND SEATBACK WENT ALL THE WAY BACK. DRIVER STOPPED VEHICLE, AND ADJUSTED PROPERLY AND RESUMED TRAVELING TO DESTINATION. HAS BEEN TAKEN TO DEALER. NO INJURIES OR ACCIDENTS HAVE OCCURRED.*AK

THE SEAT FRAME ON THE DRIVERS SIDE HAS BROKEN AWAY FROM THE REST OF THE SEAT FRAME CAUSING IT TO ROCK BACK AND FOWARD. THE MOUNT IN THE FLOOR NOW HAS BEARING THAT MOVE THE SEAT TRACK THESE ARE WORN FROM ALL THE MOVEMENT IN THE SEAT.

DRIVERS SEAT MOUNT FAILED. SEAT FRAME BROKE CAUSING SEAT TO ROCK BACK AND FORTH. SEAT COULD BREAK FROM MOUNT DURING AN ACCIDENT OR SUDDEN STOP.

THIS VEHICULE HAS A DRIVERS POWER SEAT, UPON PULLING OUT ONTO THE ROAD THE SEAT BROKE LOOSE FROM ITS MOUNT. I DID HAVE BOTH HANDS ON THE STEERING WHEEL AT THE TIME AND WAS ABLE TO KEEP CONTROL OF THE VEHICULE AS IT LIFTED FROM THE FRONT LEFT MOUNTING BRACKET. AFTER LOOKING AT THE SEAT I DISCOVERED THAT THE SEAT MOUNTING BRACKET ON THE LEFT SIDE OF THE SEAT IS BOLTED INTO THIN SHEET METAL TO THE SEAT FRAME AND NOT INTO THE SEAT FRAME RAIL. THIS APPEARS TO BE A DESIGN PROBLEM SINCE THE PASSENGER SEAT FRAME RAILS ARE BOLTED TO THE SEAT BRACKETS AS SHOULD BE. I CONTACTED THE DEALER AND HE SAID THEY WOULD FIX IT , BUT THAT I WOULD HAVE TO PAY FOR THE NEW SEAT FRAME AND LABOR AS A NORMAL SERVICE CALL. CONTACTED THE CUSTOMER ASSISTANCE LINE AND FILED A REPORT AND WAS TOLD IT WOULD BE PUT ON FILE AS A COMPLAINT FILE # C01348445, HAVE NOT HEARD ANYTHING IN A WEEK. I WILL BE FIXING THE SEAT MY SELF IN THE NEAR FUTURE BY TAKING 3/16 X 1 1/2 FLAT BAR AND BOLTING IT TO THE SEAT SUPPORT BRACKETS AND BOLTING THE SEAT FRAME TO THE FLAT BAR. WILL TRY TO TAKE PICTURES OF THE PROBLEM BEFORE IT IS FIXED AND AFTER IT IS FIXED, ANYWAY THE DAMAGE PART WILL STILL BE THERE AS THE FLAT BAR WILL JUST GIVE IT STRENGTH. WHAT IT APPEARS TO LOOK LIKE IS THE VEHICULE HAS A FULL SIZE SEAT INSTALLED ON SUPPORT BRACKETS MADE FOR A S10 SIZE VEHICULE. IF MY SEAT BROKE I AM SURE THERE ARE OTHERS THAT HAVE THE SAME PROBLEM OR WILL HAVE THE SAME PROBLEM AS IT IS JUST A MATTER OF TIME, THEY MAY NOT BE SO LUCKY AS I WAS.