2006 BMW 3 Series Engine

I AM YET ANOTHER BMW OWNER REPORTING VALVE VMCOVER GASKET ISSUES. BMW IS NOT BEING MADE TO RECALL THIS PART. ALUMINUM BOLTS THAT NEVER SHOULD HAVE BEEN USED AND WERE LATER REPLACED GOING FORWARD BUT HAVE NOT BEEN ADDRESSED. THIS IS A SERIOUS CONCERN FINANCIALLY FOR COUNTLESS OWNERS THAT HAVE HAD TO GET THESE FIXED, AND IS A SAFETY CONCERN AS LEAKING OIL COULD CAUSE ENGINE FIRES. MAKE THIS RIGHT NHTSA BY HOLDING BMW RESPONSIBLE FOR THIS DEFECT THAT THEY HAVE BEEN WELL AWARE OF FOR TEN YEARS.

CYLINDER HEAD GASKET IS LEAKING OIL DUE TO FAULTY BROKEN ALLUMINUM BOLT. THREE BOLTS ON THE FORWARD RIGHT SIDE OF THE ENGINE IS BROKEN MAYBE DUE TO ENGINE STRESS. OIL IS LEAKING TO THE EXHAUST AND I'M AFRAID IT WILL CAUSE FIRE. I READ IN THE FUROM WITH THE SAME PROBLEM. BMW SHOULD MAKE A RECALL ABOUT THIS PROBLEM.

NOTED VIBRATION WITH VEHICLE RUNNING IN GEAR WHEN STOPPED, DURING INSPECTION NOTED BOLTS ON RIGHT SIDE MOTOR MOUNT BROKEN OFF FLUSH WITH THE ENGINE BLOCK, FOUND BOLT HEAD WITH ABOUT 1" OF THREADS LAYING ON TOP OF LOWER ENGINE COVER.

FOUND OUT TODAY, AFTER MAY ATTEMPTS TO RESOLVE A NOISE IN THE FRONT END. THE RIGHT FRONT MOTOR MOUNTS BOLTS HAD BROKEN, CAUSING THE ENGINE TO MOVE VERY FREELY INSIDE THE ENGINE. THIS WAS ONLY FOUND OUT AFTER A COMPLETE RIGHT FROM DRIVE AXLE FAILURE DUE TOT HE POSITION OF THE ENGINE CAUSING THE CV BOOT TO RUB THE SUB FRAME. THIS CAUSED A COMPLETE LOSS OF CV GREASE, AND SUBSEQUENT FAILURE OF THE CV JOINT. THE CV JOINT THEN PROCEED TO GRENADE WHILE DRIVING OVER SOME RAIL ROAD TRACKS. THE OUTER AXLE THEN DROVE ITSELF INTO THE GROUND CAUSING THE VEHICLE TO RISE, AND LOSS OF CONTROL FOR A BRIEF MOMENT. THE CAR CAR TRAVELING AT APPROXIMATELY 25 MPH. UPON FURTHER INVESTIGASTION I FOUND THIS IS NOT AN ISOLATED INCIDENT WITHT HE MOTOR MOUNT BOLTS SHEERING OFF FLUSH TO THE ENGINE.

I HAVE 77,000 MILES ON THIS CAR AND THE WATER PUMP HAS BECOME DEFECTIVE AS I BEGAN TO SEACH ONLINE ABOUT THIS ISSUE I SEE THERE ARE THOUSANDS OF COMPLAINT ABOUT THE SAME YEAR AND MODEL OF MY CAR I BELEIVE THIS PART SHOULD BE RECALLED

BROKEN CYLINDER HEAD BOLT NEAR OIL FILTER HOSING FOUND THIS TO BE A VERY VERY COMMON PROBLEM WITH (N52) ENGINES. *TR

PLEASE WITHDRAW THE RECENTLY FILED COMPLAINT CONCERNING THIS 2006 BMW FROM YOUR RECORDS. THE CONFIRMATION NUMBER (ODI NUMBER) IS: 10678988. FURTHER RESEARCH HAS INDICATED THAT THE INFORMATION IN THE COMPLAINT WAS OBTAINED FROM AN INACCURATE SOURCE. THEREFORE, THE COMPLAINT IS BEING WITHDRAWN. THANK YOU FOR YOUR CONSIDERATION IN THIS MATTER. *TR

ONE OF MY VALVE COVER BOLTS BROKE CAUSING THE OIL TO LEAK EVERYWHERE. *TR

I HIT A BUMP IN THE ROAD, COMPLEMENTS OF MOONACHIE, NEW JERSEY ROUTE 120, NEW JERSEY HAS THE WORST ROADS IN THE COUNTRY AND ONE OF THE HIGHEST TAXES TOO. I HAD AN AUTO PARTS PLACE THAT SOLD ME 2-STRUTS-2 SHOCKS, WHICH THE ROADS RIPPED APART ON MY CAR TELL ME, HE'D BE OUT OF BUSINESS IF IT WASN'T FOR NEW JERSEY. AFTER I HIT THE CRATER IN THE ROAD I FELT A LOUD RATTLE BUMPING SOUND WHEN I SLOWED DOWNED AND ACCELERATED, THE ENGINE NEVER REALLY IDLED RIGHT AFTERWARDS. I HAD A FRIEND LOOK AT THE CAR AND HE TOLD ME ALL FOUR BOLTS CONNECTED TO THE MOTOR MOUNTS, ALL OF THE BOLTS SEPARATED AND BROKE OFF IN THE ENGINE, THEY SNAPPED OFF COMPLETELY AND BROKE THE MOTOR MOUNTS AS WELL. I HEAR FROM READING ON THIS SITE THE BOLTS WERE A MANUFACTURES REJECT, FAULTY BOLTS. THAT BEING SAID , I WISH I COULD LITIGATE AGAINST BMW FOR USING THE BOLTS AND THE STATE OF NEW JERSEY FOR NOT PROPERLY CARING FOR THE ROADS AND LEAVING HAZARDOUS CONDITIONS ON THE ROADS WHICH I MIGHT ADD BE FATAL FOR SOME UNFORTUNATE PERSON. VISIT HOBOKEN , NEW JERSEY AND CHECK OUT THEIR MAIN STREET, WASHINGTON, THE ROADS IN NEWARK, NEW JERSEY ARE MUCH BETTER THAN THERE.COULD NEW JERSEY'S POLITICIANS BE STEALING THIS MONEY SET ASIDE FOR ROAD REPAIR? NAH, OF COURSE NOT, IN NEW JERSEY? *TR

COOLANT LEAKING FROM RESERVOIR TANK. A COMMON ISSUE AMONG BMWS- AND IS CURRENTLY EFFECTING MY 330XI 2006. THE EXPANSION TANK IS FAULTY AND WONDERING IF THE TANK AND HOSES ARE TESTED TO EVEN WITHSTAND THE "BMW BRAND" NAME COOLANT. *TR

MY WIFE OWN A 2006 BMW 325I, WE BOUGHT IT NEW, AND SINCE DAY ONE WE COMPLAINT TO OUR DEALER THAT THE ENGINE KNOCKS. WE WERE TOLD THAT THEY HAD SIMILAR COMPLAINTS BUT CAN'T FIX THE PROBLEM. THUS, THEY GIVEN US A PAMPHLET ON HOW TO START THE CAR IN THE MORNING. OVER, THE YEARS I HAVE TAKEN IT BACK TO THE DEALER BUT TO NO AVAIL. WE PURCHASED OUR CAR AT BMW OF TOWNSON AND DO ALL OF OUR SERVICES AT RUSSELL BMW. BOTH DEALERS ARE IN THE STATE OF MARYLAND. THEY DO HAVE ALL THE RECORDS OF OUR SERVICES AND COMPLAINT PERTAIN TO ENGINE KNOCKS. RECENTLY, THERE ARE LOTS OF RECALLS WHICH INITIALLY CAR MAKERS WOULD NOT VOLUNTARY DO IT UNTIL IT IS SCRUTINIZE BY NHTSA. I WONDER IF YOU WOULD LOOK INTO THIS ISSUE. THANK YOU VERY MUCH FOR YOUR TIME AND ATTENTION. I CAN BE REACH AT [XXX] OR MY CELL [XXX]. [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6). *TR

ENGINE VALVE COVER HEAD BOLTS SNAPPED. QTY. 3. *TR

BMW NA HAS ISSUED A RECALL TO ADDRESS BROKEN HEAD BOLTS IN A NUMBER OF 2010 MODELS, WHICH CAN RESULT IN ENGINE FAILURE. I HAVE SPOKEN WITH SEVERAL BMW OWNERS AND FOUND THAT THIS ISSUE EXTENDS BEYOND THEIR INITIAL RECALL INTO EARLIER MODELS, BUT BMW NA IS IGNORING THE ISSUE OUTRIGHT IN THE HOPES THAT IT WILL DISAPPEAR. I HAVE SPOKEN WITH BMW NA SEVERAL TIMES AND THEY HAVE GIVEN ME THE RUNAROUND FOR SEVERAL MONTHS AND PUT MAJOR SMOKESCREENS UP IN MY ATTEMPT FURTHER THE CONVERSATION/INVESTIGATION OF THE ISSUE. I'M REACHING OUT TO NHTSA BECAUSE I HAVE NO OTHER RECOURSE AND I KNOW THIS ISSUE IS NOT A LOCALIZED ISSUE WITH ONE YEAR MODEL, BUT SYMPTOMATIC OF SEVERAL YEARS AND MODELS. PLEASE HELP THE DRIVING PUBLIC BY ASSISTING ME IN ADDRESSING THIS ISSUE WITH BMW.

THERE IS A CLEAR MANUFACTURER DEFECT CONCERNING THE ALUMINUM BOLTS ASSOCIATED WITH THE VALVE COVER GASKET ON THE BMW 2006 325I'S. WITH RESEARCH THAT I HAVE BEEN DOING FROM OTHERS, I NOTICED THAT THIS IS A MANUFACTURE DEFECT AND BMW DOES KNOW ABOUT THE PROBLEM. THIS CAN BE A SAFETY CONCERN IF NOT CORRECTED QUICK DUE TO THE POSSIBILITY OF OIL FALLING ON TOP OF THE EXHAUST PIPE AND MAY CAUSE A FIRE.THE DEFECTIVE BOLTS POSE A SERIOUS POTENTIAL RISK TO THE SAFETY OF THE OWNERS OF THESE VEHICLES, AS WELL AS TO OTHER DRIVERS WHO SHARE THE ROADWAY WITH THEM. I RESPECTFULLY REQUEST THAT BMW NORTH AMERICA ISSUE A VOLUNTARY RECALL OF THE BMW 2006 325I'S AFFECTED BY THIS MANUFACTURER DEFECT. I AM NOT PRIVY TO WHAT CONSTITUTES A VEHICLE'S DEFECTIVE COMPONENTS TO REACH A "RECALL STATUS". *TT

TL* THE CONTACT OWNS A 2006 BMW 330I. THE CONTACT STATED THAT FUEL WAS LEAKING FROM THE OIL FILTER HOUSING. THE VEHICLE WAS TAKEN TO AN INDEPENDENT MECHANIC. THE TECHNICIAN DIAGNOSED THAT THE BALL COVER GASKET NEEDED TO BE REPLACED. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. THE APPROXIMATE FAILURE MILEAGE WAS 87,243.

I AM THE ORIGINAL OWNER OF 2006 325I WITH 42,000 MILES. ON JANUARY, THE CAR SUDDENLY ALARMED WARNING SIGNS ON CA HIGHWAY #5 AND STARTED TO MAKE LOUD NOISE AND SHAKINGS. AT THAT TIME, I WAS PREGNANT AND WITH MY 2 YEAR OLD BABY ON BACK SEAT. THE SITUATION WAS HAPPENING ON THE HIGHWAY! I WAS SO WORRIED ABOUT DRIVING SAFETY. TO SOLVE THE PROBLEM, THE DEALER SHOP ASKED ME TO REPLACE HEAD GASKET ALUMINUM VOLT AND HOUSING GASKET. IT DID COST OVER $4000. DURING THE REPAIR, THE TECHNICIAN SAID THAT THE PROBLEM IS COMMON ON THIS MODEL. I RESEARCHED ABOUT THIS PROBLEM AND READ MANY COMPLAINTS ABOUT SAME ISSUES FROM BMW 2006 325I OWNERS. THE OWNERS AGREE THAT THE HEAD GASKET ALUMINUM VOLT AND HOUSING GASKET ISSUE RESULT IN MANUFACTURE DEFECTS. LATER, BMW CHANGED THE VOLT MATERIALS AND PROVIDED GOOD WILL REPAIRS FOR SOME OWNERS. I STRONGLY ASSUME THAT THIS IS ONE OF MANUFACTURE DEFECTS COST CUSTOMERS TO REPAIR AS WELL AS THREATEN DRIVERS? SAFETY. SO I CALLED BMW CUSTOMER RELATION. BUT THEY SAID THAT ?KEEP THE RECEIPT AND YOU MAY GET REFUND WHEN ?THERE ARE ENOUGH PEOPLE COMPLAIN ABOUT IT???YOU ARE MORE THAN WELCOME TO REPORT THIS PROBLEM TO NHTSA?.? I ASKED ABOUT HOW MANY CUSTOMERS HAD SAME PROBLEMS. BUT THEY SAID "DO NOT KNOW". BASED ON THEIR RESPONSE, IT SEEMS THAT THEY KNEW AND UNDERSTOOD IT IS MANUFACTURE DEFECTS, BUT DO NOT CARE UNTIL THE ISSUE IS LOUSY OR HANDLED WITH POWERFUL AUTHORITY. IT IS THREATENING DRIVING SAFETY OF NOT ONLY THE OWNERS BUT ALL OTHER DRIVERS ON HIGHWAYS BECAUSE IT DOES NOT GIVE ANY SIGNS BEFORE BROKEN ON HIGHWAY. THEREFORE, I AM REPORTING THIS ISSUE WHILE HOPING THAT NO OTHER DRIVERS OR BABIES GET HURTS FROM THIS SUDDEN DEFECTS AND YOU COULD DO INVESTIGATE IT IN DEPTH SO THAT YOU COULD PROTECT ALL OTHER DRIVERS? LIFE. *TR

WHEN STARTING FROM IDLE TO RUNNING STATE AT A STOP LIGHT THE WHOLE CAR STARTED SHAKING. TOOK THE SHOP AND THEY SAY IT A FAULTY COIL/SPARK PLUG. COSTS ME $600-$1000. LOOKS LIKE THIS IS A COMMON PROBLEM IN BMW 325I 2006. THEY SHOULD FIX THIS. *TR

A BOLT BROKE ON THE VALVE COVER. IT'S NOT FROM COLD WEATHER OR LACK OF MAINTENANCE, IT'S CLEARLY A MANUFACTURER DEFAULT. WHEN ADVISED BY VALLEY BMW IN MODESTO I LEARNED THIS HAPPENS IN MOST OF THESE MODELS THAT YEAR. IT'S FROM OVER TORQUING THE BOLT OR A FAULTY BOLT OR SOMETHING ELSE BUT IT'S CLEARLY NOT THE FAULT OF THE CONSUMER. MINE BROKE ON THE PASSENGER SIDE AND IT CAUSES THE OIL TO LEAK ON THE EXHAUST. THIS IS A SAFETY ISSUE AND MUST BE ADDRESSED IMMEDIATELY. THIS ALSO HAPPENS ON THE OIL PAN! HTTP://MSAUCEDA1.BLOGSPOT.COM/2013/07/BMW-330I-2006-BROKEN-BOLTS-VALVE-COVER.HTML IT COSTS OVER $1000 TO FIX AND AFTER RESEARCHING FURTHER, I FOUND THIS IS HAPPENING A LOT AND MANY CONSUMERS AS WELL AS REPAIR SERVICES ARE FRUSTRATED AND UNDERSTANDABLY ANGRY. PLEASE ADDRESS THIS AND MAKE BMW RECALL THESE VEHICLES FOR REPAIR BEFORE SOMEONE GETS KILLED! HTTPS://WWW.YOUTUBE.COM/WATCH?V=5CO92U-WA94. *TR

I AM WRITING THIS DEPARTMENT IN HOPES TO RESOLVE ONGOING MAJOR MANUFACTURING DEFECTS ON THE BMW 2006 325I'S. THE 325I MOTOR IS WELL KNOWN FOR ALUMINUM BOLTS SNAPPING ON THE MOTOR RESULTING IN SIGNIFICANT OIL LEAKS AND OIL PRESSURE. THE INTAKE MANIFOLD GASKET AND BOLTS ARE WELL KNOWN FOR PREMATURELY FAILING AND THE HEAD OF BOLTS SNAPPING OFF UNDER PRESSURES. THE VALVE COVER GASKET AND OIL PAN IS ALSO KNOWN TO PREMATURELY FAIL DUE TO POOR ENGINEERS AND THE UTILIZATION OF ALUMINUM BOLTS. BMW FIXED THE ISSUE IN 2007 AND REPLACED DEFECTIVE BOLTS WITH IRON BOLTS. THE IRONY IS THAT BMW REFUSES TO ACKNOWLEDGE THE ISSUES IN THE 2006 BMW 325I. CONSUMERS ARE ON THE HOOK FOR THOUSANDS OF DOLLARS WORTH OF REPAIR BILLS BECAUSE OF FAULTY ENGINE COMPONENTS. THE NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION HAS RECEIVED SEVERAL COMPLAINTS REGARDING THIS MANUFACTURER DEFECT. THE ALUMINUM BOLTS HAVE BEEN REDESIGNED SINCE DISCOVERING THE MANUFACTURER DEFECT. BMWNA HAVE HAD NUMEROUS SERVICE ISSUES RELATED TO THESE DEFECTIVE ALUMINUM BOLTS. THEY HAVE ALL OPENLY ADMITTED THAT THE BOLTS IN QUESTION WERE DEFECTIVE IN NATURE AND PRODUCTION, AND THAT THE BOLTS HAVE BEEN REDESIGNED TO AVOID FUTURE FAILURES. SOME OF THESE COMPLAINTS INCLUDED, AND RESULTED IN, VEHICLES LEAKING OIL IN THE ENGINE AREA CAUSING FIRES IN THE VEHICLE. THE DEFECTIVE BOLTS POSE A SERIOUS POTENTIAL RISK TO THE SAFETY OF THE OWNERS OF THESE VEHICLES, AS WELL AS TO OTHER DRIVERS WHO SHARE THE ROADWAY WITH THEM. IT IS MY STRONG BELIEF THAT THIS TYPE OF PUBLIC SAFETY RISK CANNOT GO ON ANY FURTHER WITHOUT PROPER INTERVENTION FROM THE GOVERNMENTAL AGENCIES WE EMPLOY AS TAXPAYERS. *TR

THERE IS A CLEAR MANUFACTURER DEFECT CONCERNING THE ALUMINUM BOLTS ASSOCIATED WITH THE VALVE COVER GASKET ON THE BMW 2006 325I'S. THE NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION HAS RECEIVED SEVERAL COMPLAINTS REGARDING THIS MANUFACTURER DEFECT. THE ALUMINUM BOLTS HAVE BEEN REDESIGNED SINCE DISCOVERING THE MANUFACTURER DEFECT. BMWNA HAVE HAD NUMEROUS SERVICE ISSUES RELATED TO THESE DEFECTIVE ALUMINUM BOLTS. THEY HAVE ALL OPENLY ADMITTED THAT THE BOLTS IN QUESTION WERE DEFECTIVE IN NATURE AND PRODUCTION, AND THAT THE BOLTS HAVE BEEN REDESIGNED TO AVOID FUTURE FAILURES. SOME OF THESE COMPLAINTS INCLUDED, AND RESULTED IN, VEHICLES LEAKING OIL IN THE ENGINE AREA CAUSING FIRES IN THE VEHICLE. THE DEFECTIVE BOLTS POSE A SERIOUS POTENTIAL RISK TO THE SAFETY OF THE OWNERS OF THESE VEHICLES, AS WELL AS TO OTHER DRIVERS WHO SHARE THE ROADWAY WITH THEM. IT IS MY STRONG BELIEF THAT THIS TYPE OF PUBLIC SAFETY RISK CANNOT GO ON ANY FURTHER WITHOUT PROPER INTERVENTION FROM THE GOVERNMENTAL AGENCIES WE EMPLOY AS TAXPAYERS. I RESPECTFULLY REQUEST THAT BMW NORTH AMERICA ISSUE A VOLUNTARY RECALL OF THE BMW 2006 325I'S AFFECTED BY THIS MANUFACTURER DEFECT. I AM NOT PRIVY TO WHAT CONSTITUTES A VEHICLE'S DEFECTIVE COMPONENTS TO REACH A "RECALL STATUS". I HAVE DISCOVERED THAT BMW OF NORTH AMERICA IS KEENLY AWARE OF THE DEFECTIVE ALUMINUM BOLTS, AND HAS ISSUED INTERNAL MEMOS TO THEIR STAFF CALLED "TECHNICAL SERVICE BULLETINS" (TSB) TO FOREWARN DEALERSHIPS OF THIS MANUFACTURER DEFECT, AND THE STEPS TO REMEDY THE ISSUE. I HAVE REQUESTED THIS INFORMATION FROM BMW OF NORTH AMERICA, AS WELL AS SEVERAL DEALERSHIPS; AND I WAS REFUSED. I HAVE DILIGENTLY MAINTAINED MY VEHICLE AS PRESCRIBED BY THE SERVICE MANUALS, AS WELL AS THE ON BOARD COMPUTER IN THE VEHICLE. MY CONTENTION IS EXTREMELY CLEAR; THE ALUMINUM BOLTS ARE A MANUFACTURER DEFECT! FIX THEM ALL AT NO COST TO THE CONSUMER. *TR

BROKEN CYLINDER HEAD BOLTS AT THE FRONT TIMING COVER. SYMPTOM WAS OIL LEAK AT TIMING COVER. UPON INSPECTION, THE HEADS OF 4 BOLTS HAD SHEARED OFF AND 3 BOLT HEADS HAD DROPPED THROUGH THE TIMING CHAIN HOUSING AND ENDED UP IN THE OIL PAN. *TR FIRST, HEAD BOLTS SHOULD NOT FAIL. SECOND, THE SHEARED BOLT HEADS PASS THROUGH THE TIMING CHAIN HOUSING AND COULD INTERFERE WITH THE TIMING CHAIN AND CAUSE IMMEDIATE ENGINE FAILURE.

MY 2006 BMW 330I BEGAN LEAKING OIL. AFTER INSPECTION IT WAS DETERMINED TO BE BROKEN BOLTS. THIS VEHICLE HAS BEEN PROPERLY CARED FOR. IT HAS NOT BEEN IN AN ACCIDENT AND HAS BEEN SERVICED AND MAINTAINED. AFTER ONLINE REVIEW, THIS PROBLEM HAS HAPPENED TO SEVERAL BMWS. THE OIL LEAKS ONTO BRAKES, BELTS, EXHAUST, ETC.... CAUSING A SEVERE SAFETY HAZARD. THIS NEEDS TO BE ELEVATED TO A RECALL. *TR

TL* THE CONTACT OWNS A 2006 BMW 325I. THE CONTACT STATED THAT WHILE DRIVING 65 MPH, THE LOW COOLANT LIGHT ILLUMINATED AS THE VEHICLE OVER HEATED. THE VEHICLE WAS TAKEN TO AN INDEPENDENT MECHANIC FOR DIAGNOSIS WHERE IT WAS STATED THE WATER PUMP NEEDED TO BE REPLACED. THE VEHICLE WAS REPAIRED AND THE MANUFACTURER WAS NOTIFIED. THE APPROXIMATE FAILURE MILEAGE WAS 88,000. *TR

I TOOK MY CAR TO RICHMOND BMW AND THEY TOLD ME THEY DISCOVERED I HAD BROKEN HEAD GASKET BOLTS ! I'VE BEEN DOING A LOT OF RESEARCH AND THIS IS A VERY COMMON MANUFACTURES PROBLEM ! THESE MAKE AND MODELS SHOULD BE RECALLED THIS IS VERY DANGEROUS ! *TR

I HAVE A 2006 325I SEDAN WITH 55,856 MILES ON IT. I TOOK IT IN FOR A ROUTINE SERVICE ON 4-18-2013. IT HAS BEEN MAINTAINED BY ONLY BMW DEALERSHIPS IN ITS LIFETIME WITH ALL REQUIRED MAINTENANCE DONE ON SCHEDULE. THEY CALLED TO NOTIFY ME THAT UPON INSPECTION THEY HAD FOUND THE HEAD BOLT BROKEN BEHIND THE OIL FILTER HOUSING, THE OIL FILTER HOUSING GASKET LEAKING AND THE DRIVE BELT TENSIONER LEAKING. I HAD NOT BEEN EXPERIENCING ANY OUTWARD S+S OF THIS PROBLEM. THEY QUOTED ME $3400 TO REPAIR THIS. I WAS SHOCKED THAT A CAR IN SUCH GREAT CONDITION WOULD HAVE SUCH A PROBLEM AT THIS MILEAGE. I ASKED WHY THIS WOULD HAPPEN AND ESSENTIALLY WAS TOLD IT IS UNUSUAL BUT DOES HAPPEN. THEY ADVISED A REPAIR IN THE FUTURE. I WENT HOME AND RESEARCHED THIS AND FOUND IT HAS BEEN A COMMON PROBLEM IN THIS MODEL AND THAT SUBSEQUENTLY BMW HAS CHANGED THE TYPE OF BOLT THEY USE. SO I THOUGHT I WOULD CALL THE CUSTOMER SERVICE LINE TO FOLLOW UP ON ANY ASSISTANCE FROM BMW. LONG STORY SHORT THEY TOOK THE COMPLAINT BUT BECAUSE I HAVE A LOW MILEAGE VEHICLE THAT HAS BEEN OUTSIDE OF WARRANTY FOR 3+ YEARS THEY WOULD OFFER NO HELP. YOU KNOW SHAME ON BMW THIS IS MY 4TH BMW AND VERY LIKELY MY LAST DUE TO THIS. THIS SHOULD BE A RECALL, THIS SHOULD NOT BE HAPPENING NO MATTER HOW LONG IT TOOK TO GET TO THE 50,000 MILE + RANGE WHERE THIS PROBLEM SHOWS ITSELF. *TR