2018 Dodge Durango Engine

Over time, the valvetrain in my engine became gradually louder. Because there were no check engine lights or fault codes, I initially assumed this was a normal characteristic of the engine. That changed on January 2, 2026, when I began to hear a pronounced knocking/loud tapping noise accompanied by a cylinder 8 misfire. At that point, I stopped driving the vehicle and had it towed to a repair shop. Based on the symptoms, we initially believed the issue would be limited to a camshaft and lifter replacement. However, after draining the oil and cutting open the oil filter, a significant amount of metal debris was discovered. Further inspection revealed that one camshaft lobe had been worn down nearly smooth and the corresponding lifter had failed. When the camshaft was removed for full evaluation, all other lobes showed normal, even wear. Only the lobe associated with the failed lifter exhibited catastrophic damage beyond repair. As a result of the metal contamination throughout the engine, a full engine replacement was required rather than a repair of individual components. The basis of my complaint is that this failure appears to be a well-documented and common issue with the 6.4L HEMI engine equipped with MDS. I have since reviewed numerous reports and forum discussions describing nearly identical failures—often beginning with increased valvetrain noise, followed by a single-cylinder misfire and extensive internal damage. This was not the result of neglect or abuse, but rather a known failure mode that ultimately led to the complete loss of the engine.

3.6L V6 Engine, Auto Start/Stop light came on followed by check engine light. Codes for multiple misfires, replaced multiple coils and replaced all spark plugs. After all was replaced, still had the same issues. Took it to a local Dodge dealership and they said it was a head gasket but it would have to be sent off to figure out which one.

2018 Dodge Durango GT with 47,000. The check engine light came on. Took it to a Dodge dealer for service. Diagnosis was head gasket failure, allowing coolant into the cylinder causing engine misfire and potential overheat and a blown engine. This appears to be an ongoing issue with the Penstar V6 engine. This is a safety concern because the vehicle may break down while driving or overheat without warning, creating a power loss while driving

Right hand and left hand intake camshaft were damaged by the slider rocker finger follower. Cylinder 5 was the worst. Metal was sent through the overhead and got into the intake phaser. Parts were recently removed by the dealer and should be available if request is made shortly. Failure was found prior to catastrophic failure due to noise from the engine compartment. Vehicle was dropped off in the overnight drop box to allow vehicle the best chance to replicate the noise. Noise was only noticeable during cold starts below 30°f at idle and no load. Once the car warmed up, the noise was much less noticeable and could easily have been overlooked. No check engine lights were illuminated. If problem was not corrected, I'm confident this vehicle would have left me stranded by loss of power during driving putting me and my family in an unsafe situation. I first noticed the objectionable noise in November 2024 but was unable to get it to replicate reliably so a dealer could diagnose it. The problem was replicated by a dealer and components were replaced under warranty @ 53,272 miles. Oil changes were completed in line or ahead of the oil life monitor system in the cars instrument cluster. This seems to be a cold climate design issue with no oil being provided to the intake camshaft to sliding rocker finger follower interface during start up as oil appears to be fed from exhaust side lash adjuster. I suspect this same issue will reappear as the replacement parts are the same with no apparent improvements. Since the repair I've noticed improved fuel economy, smoother accelerations and shifts, and overall less noise. The degradation of these things before was slow enough to be unnoticeable.

While driving on the Thruway, the vehicle tends to misfire which results in lost power to the engine and shaking of the vehicle. The check engine light starts flashing and it becomes unsafe to maintain speeds. The issue was diagnosed as Cylinder 5 Misfire caused by camshaft and lifter failure. This sudden loss of power while driving at highway speeds could cause an accident if it happens during traffic or passing situations. This is a known issue with the 2018 Dodge Durango GT V6 and should be a recall on the vehicle. This is a major engine issue.

My vehicle began to misfire after driving roughly 8 miles, check engine light would flash and ding. After shutting vehicle off for a while and restarting it, problem would be gone until driving approximately 8 miles. Brought to Chrysler service center, where they reproduced the problem and determined it is a camshaft or camshaft related issue. Vehicle is parked at that service center awaiting parts that are backordered until January. Vehicle cannot be driven in this condition. If the camshaft fails catastrophically, it could destroy the entire engine, putting myself and whoever else is in the vehicle in danger.

I bought this car, brand new off the dealer and it has been in perfect shape until 120,000 miles. All of a sudden the check engine light comes in and turns out it was the head gasket!! 5 years old, hasn't needed a thing and the mechanic tells me I need a new engine!? What good is it if I buy a brand new car and take perfect care of it all to end up with the engine going to [XXX]. I have heard other people saying the same thing with their 3.6l pentastar engine. AT 120K...I don't see that being a coincidence if it keeps happening with the SAME engine at the SAME AMOUNT OF MILES. There is definitely a problem here. P.s won't let me upload documents on the mechanics diagnosis. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

The contact owns a 2018 Dodge Durango. The contact stated after attempting to start the vehicle, the engine failed to turn over. The contact then stated that after several attempts to start the vehicle she smelled a burning odor. No warning lights were illuminated. The AAA was notified of the failure and the battery was replaced; however, the failure recurred. The vehicle was then towed to the dealer where the contact was informed that coolant had leaked in the engine and burned the starter; however, the vehicle was not diagnosed or repaired. The vehicle was not repaired. The manufacturer was notified of the failure and the contact was informed that the repair cost would be covered. The failure mileage was approximately 65,000.

2018 Durango GT purchased at 30k miles and the oil pan gasket was already worn and leaking oil. Tensioner and pulley also failed. Seems like Mopar utilize low quality parts in general, as minor as they may seem they are vital for me to operate my vehicle safely.

MY CAR IS A DODGE DURANGO SRT8, YEAR 2018 , VIN# [XXX], WITH ONLY 20,000 MILES AND THE ENGINE TRANSMISSION BROKE. IT IS UNDER GUARANTEE AND THE DEALER HAS BEING COMPLIANT. I AM AFFRAID THAT IN THE WEB MEDIA MORE OWNERS WITH THE SAME ENGINE ARE EXPERIENCING THE SAME ISSUE AS ME. THERE IS A NOTIFICATION THAT THE ENGINE HAD A FACTORY ERROR IN THE MANUFACTURING, THEY MENTION A PARK LOCK ROD CAUSING PROBLEMS WITH THE TRANSMISSION. I AM SEARCHING IF THERE IS ANY RECALL, BUT IT SEEMS THAT THE PROBLEM IS BEGINNING TO FLOURISH. PLEASE I WILL APPRECIATE MORE INFORMATION AND SUGGESTION FROM YOU OF WHAT SHOULD I DO. THANKS. INFORMATION Redacted PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6).

Doing some checking problems with this particular vehicle it seems that the water pump/ radiator has problems. My vehicle has a anti-freeze leak when at idle leaving a stream in the driveway. Thus causing a problem for pets and wildlife. The engine warning light has come on. The a/c compressor makes a noise also. FYI.