2011 Mercedes-Benz C-Class Suspension

Subframe rusted resulting in failure of left rear suspension mount causing dangerous loss of control of car under braking.

Rear tires were down to steel belt after replacing August 1, 2022 and less than 10,000 mile wear. I took the car to a dealership for diagnosis. The rear subframe is completely corroded and failed causing extreme wear on tires and a DANGEROUS DRIVING SCENARIO. I’ve researched and see this is a common problem on these Mercedes cars. Why is there no Mercedes recall or accountability for this common issue?This is a serious issue that could cause serious accidents and bodily harm or death..

I was teaching my 16 year old son how to drive when he got his learners permit . When we got onto the highway a car cut him off and he had to apply a firm steady brake . When breaking the car swerved from the rear into the other lane , nearly striking another vehicle . This also resulted in a loss of control when applying heavy breaking after I had him pull over and I took control of the vehicle once I was able to get the car to the shop I pulled the rear wheel s off and inspected the brakes , which were found to be in good condition . I looked around the vehicle and noticed where the rear driver side subframe connected to the control arm broke off from a manufacturer defective weld or poor selection of materials . component. Upon inspection both sides are perforated and have lost structural integrity. Many other vehicles of the model type have reported similar issues online. This is a serious safety concern that will happen to 100% of these vehicles. A recall needs to be issued by Mercedes for this immediately. This vehicle has very little rust anywhere except at these connections .

I was driving my 2011 MB C300 40 MPH on a straight suburban road when the light turned red. I applied the brakes and heard a clunk from the rear. Surprisingly, the car swerved with a right turn yaw moment. Normally I enjoy driving my car, but that never happened before. So I tried it again in the next block and it yawed again. That’s not right. My mechanic happened to be just down the road so I pulled in. He told me that the rear subframe had rusted out and the car was unsafe to drive. Furthermore, he would not attempt welding it because the metal is too far gone. A new replacement part is unavailable from the dealership and back ordered from Germany for months. Used part will also be rusty. My car with 77k miles on it is suddenly worthless. Mercedes-Benz “The Best and then Nothing”

While driving home last night (with passenger), I experienced a sudden pull to left and wobble\oscillation of the car when I made steering corrections to prevent vehicle from going into oncoming traffic. Car seemed to behave normally except whenever I applied the brakes. I proceeded home, where I inspected for the obvious such as brake calipers, pads. rotors etc. Then I removed the rear left tire. This was due to a clunking sound that seemed to come from that area. Everything looked OK until I saw a front lower suspension part (a plastic covered pressed metal strut connecting the lower part of the wheel\rotor assembly to large U-shaped frame member which had multiple welded attachments and brackets) just hanging there unattached on one (forward) end. The bracket it was bolted to was just sheared off. Looked like it rusted to the point of finally tearing itself off of the frame. There was no warning of this condition either by sensors/lights/etc. or the performance of the vehicle when driving it. The defective braking action was sudden. This is NO SMALL ISSUE! After reading of the numerous reports of this very same problem I have to say I am amazed that NOTHING IS BEING DONE TO PREVENT THE FIRST DEATHS AND INJURIES THAT WILL MOST LIKELY OCCUR FROM THIS. This is a danger to the occupants of the principle vehicle, pedestrians, as well as other vehicles in the immediate vicinity, moving or stationary. This can happen at high speeds, slow speeds, in traffic with other vehicles around the car or humans on sidewalks. I can clearly see that this is not a small repair as it looks like the entire rear assembly would need to be taken apart and reconstructed in order to replace the part. I have also read that this issue is not only common but that it has been recalled in Canada and Europe by Mercedes for repair. I guess we are waiting for the first deaths to occur before our American safety agencies can take action? Really?

Rear suspension crossmember mounting point for one of the control arms broke off allowing control arm to fail. Possible entire wheel assembly could now fail creating dangerous driving conditions especially at higher speeds. Took to a shop and confirmed. Called Mercedes dealership and they said it was not covered by a recall even though in Europe I believe it is. Many websites have said this is an ongoing and common problem.

Rear Sub frame faiIure / rusted and rotted On this site alone there are complaints listed under 3 different heading Structure (30) / SUSPENSION (38) / UNKNOWN OR OTHER (20) all related to the rear sub frame. not to mention 100's on the web. I nearly died when I hit the brakes the car lurched to the left at highway speed. My mechanic told me that the rear Subframe was rotted and the rear control arm is no longer connected to the sub frame He insisted that the car is UNSAFE to drive. He was very surprised as the car only has 70,000 miles on it and in good shape with no rust anywhere else on the car. I did a quick search of the issue on the web and immediately found that MB has had this issue across the world in various models manufactured in 2011-2014. Presently, there are recalls in Germany and Canada for this issue. I contacted my MB Service department and was informed that no recall for this issue exists in the US and they would not cover the costs to repair. The repair could cost between $5k to $7k They told me that I would need to contact MB North America Customer Service. I find it amazing that MB Service, Dealers and North America HQ are all aware of this issue but the Company will not issue a recall or stand behind their product. This not some minor defect. When a major structural component of the car is compromised the lives of vehicle occupants and others on the road are at risk of death due to a major accident. The vehicle is now undriveable and will cost several thousands of dollars to repair. MB is fully aware of this issue and refuses to do anything about it. NHTSA needs to address this issue and make the Manufacturer stand behind their Quality pledge which as a consumer you are paying for when purchasing what you expect to be exceptional German engineering and what you are given is a a product with a known defect that will not be addressed.

What component or system failed or malfunctioned, and is it available for inspection upon request? Rear subframe has rusted out and left side arm has separated- my car has been routinely maintained and primarily housed in garaged parking. It does not have a history of flood or water damage. How was your safety or the safety of others put at risk? My steering and breaking was impacted even at low speeds < 30 MPH. Has the problem been reproduced or confirmed by a dealer or independent service center? - Vehicle failed a Maryland state safety inspection and was deemed unsafe to drive. Has the vehicle or component been inspected by the manufacturer, police, insurance representatives or others? Yes, inspected by Maryland state certified safety inspector Were there any warning lamps, messages or other symptoms of the problem prior to the failure, and when did they first appear? I noticed decreased accuracy in my steering upon breaking and decreased function in breaking- my inspection revealed that all breaks were intact and working.

Rear Sub-Frame completely rusted out on car that has only 68800 miles and garaged kept since new. The suspension failure is an obvious engineering issue. No rust anywhere else on the car. The vehicle sways and bangs there is almost no metal left on the framework that all of the other rear suspension components mount to and rely on for stability. I have pictures to show what an obvious pre-mature failure this is from a touted high end auto manufacturer. Mercedes Benz should be investigated and made to repair these vehicles.

Rear Subframe Rot. The vehicle was purchased July 2021 from Automax Of Frederick Maryland. I took the car to Euromotors of Bethesda and they informed me about the issue so I took it back to the dealership because the car was sold to me like this and the owner of the dealership let me know that his "guys" would have never passed it in the MD inspection if a hole was about to be there or severe rust. However it was still sold and now I have the problem of where one of my control arms are rusted out and the car is not safe to drive. The dealer also let me know that the rust was just "surface rust" and it was nothing to worry about. The dealer ask me to bring the car in to inspect and lifted and let me know they would put a ticket on it if the car gave me any problems they would take care of it. Never got anything from them.

I was driving my C 2011 MB and suddenly when applying the Brakes the car had a severe pull to the left and a loud noise from the rear driver side wheel. I made an appointment with my mechanic to have the issue looked at. There were no warning lights or other symptoms until basically the complete failure of the rear suspension. My mechanic informed me that the rear Subframe of the suspension on the vehicle had completely rusted out and the components holding the brake assembly and sway bar were almost at the point of becoming disengaged from the vehicle. He stated that the car is unsafe to drive. He was very surprised as the car is garage kept an in good shape with no rust anywhere else on the car. I did a quick investigation of the issue on the web and immediately found that MB has had this issue across the world in various models manufactured in 2011-2014. Presently, there are recalls in Germany and Canada for this issue. I contacted my MB Service department and was informed that no recall for this issue exists in the US and they would not cover the costs to repair. They told me that I would need to contact MB North America Customer Service. I find it amazing that MB Service, Dealers and North America HQ are all aware of this issue but the Company will not issue a recall or stand behind their product. This not some minor defect. When a major structural component of the car is compromised the lives of vehicle occupants and others on the road are at risk of death due to a major accident. The vehicle is now undriveable and will cost several thousands of dollars to repair. MB is fully aware of this issue and refuses to do anything about it. NHTSA needs to address this issue and make the Manufacturer stand behind their Quality pledge which as a consumer you are paying for when purchasing what you expect to be exceptional German engineering and what you are given is a a product with a known defect that will not be addressed.

The rear subframe rotted and broke as I was driving. I almost got into a bad accident. This apparently is a common & deadly issue that MB is aware of. Unacceptable that there is not a recall.

Manufactory defect on w204 Chassis Mercedes Benz rear sub frame rusting allowing control arm to brake free affecting safety and drivability control loss, which has or could lead to severe accident. There no recalls for this defect and is a common issue with materials on back order for the rear sub frame, vehicle Is not drivable until frame is replaced.

My C300 2011 is having rear suspension problem which is unsafe to drive. I took in my car for my usual maintenance check and was told by the mechanic that the rear left driver side suspension is rusted and rotated out, to the point that it can break off and cause an accident. As Mercedes product, even the mechanic was surprised to see this happen on this car. Not surprised the dealer told me there is no recall at this time. I am still waiting for a quote but from what I've seen other people complaining with the same exact issue in same make and model. I have attached pictures just in case.

I am reporting a big safety hazard issue on these Mercedes C300 model year 2011. The suspense bracket just breaking off with obvious no visible issues. The suspension support bracket is got rotted with rust from inside out and broke off while driving on the highway. The issue was obvious when I braked suddenly and the car just pulled itself to the right side. This could easily cause an accident. I reported the incident to Mercedes and they told me to report to NHSTA and they cannot do anything. Once home and jacked up the vehicle I found that the bracket was completely off the frames and it did hit the gas tank causing a dent in the tank (a big safety issue) seam. I googled the issue and it seems like it is a known issue with these models and Mercedes have not recalled or fixed this issue on any vehicle. I have attached pictures of the broken bracket. Thank you

I took the car to Mercedes for service and they found that the rear suspension frame had extensive rust and recommended that it should be replaced. The car only has 87,000 has been garage kept since buying the car in 2013 and has been serviced my MB. The frame has two quarter size holes at the same location on the left and right sides. MB was made to recall this in both Canada and Europe. MB stated that this is a known issue with this car. Why has the NHTSA not forced MB to recall this car? MB knows that if part fails the entire rear drivetrain separates from the car. My understanding is this effects most C-class E-class cars, plus the repair is over $4,000.00 This should be on MB not the consumer.

The car started fishtailing slightly when the brakes were applied at speeds around 25 MPH. First it was taken to a Mercedes dealership on June 24th where they said it need a sway bar and tires. They were not sure that would address the issue. When we went to get tires, the tire person said the control arm was connected to nothing in the rear. The rear subframe was rotted to the point that there was not a place to even weld it back on to and needed to be entirely replaced. The fact that Mercedes missed it is shocking in itself, I can only assume (we bought the car used) it was rotted from use in winter weather before we got it. The repairs have been estimated to cost between $2200-3800-.

1. Rear Subframe of the car rusted out, causing car to suddenly jerk to the right while braking. as inspected by my mechanic, the driver side part of the rear subframe is also about to fail as well 2. The sudden jerky movement can probably cause me to lose control and possibly crash into another vehicle, potential hurt myself and other cars around me 3. Yes, the problem has been reproduced and confirmed by an independent service center 4. The vehicle or component has not been inspected by the manufacture, police, insurance representatives. It's only been inspected by my mechanice. 5. No warning lamps or symptoms appeared prior to subframe failure

Tried to get alignment and was told rear sub frame is rotted. Must be replaced. Car is garaged. Serviced at dealer. This shouldnt be happening. Car was involved in accident (mainly passenger doors damaged) which triggered us to need to get new tire which alerted us to alignment cant be completed and told to not drive car it's not safe due to rotted subframe.

I was driving down the road when a deer ran out into the roadway ahead of me. I applied the brake firmly and hear a "pop" and the car suddenly changed lanes. I was able to recover without much of an incident but applying the brakes from that point on caused the car to "steer" into a new direction. I took the vehicle out to a friends farm and jacked it up to find that on this car with zero other corrosion issues that the mounting point for one of the rear suspension arms had rusted at the weld and broken off the sub frame. I should note that the rest of the underbody was inspected and the rear subframe is the only place that has any corrosion. Research into this issue over the past few months has lead me to countless people being affected by the same issues. This is not an isolated case and it needs to be addressed by the manufacturer before it causes a fatal accident (if it has not already).

I noticed that when using the brakes the car would pull to the side. The front brake rotors and pads were completely replaced but the pulling behavior remained unchanged. When the mechanic specifically looked for reasons for the pulling he found the rear driver's side stabilizer completely rusted through and the passenger side one showing signs of similar impending failure. I took pictures of both. The driver's side arm that was broken was also rubbing against the gas tank. The company, Mercedes, is only allowing replacement parts to be delivered when ordered by VIN, so I can't get a part already in the US (it has to be ordered directly from Germany and specifically for my car's VIN - they KNOW there's a problem).

the rear subframe rotted away

Due to design flaw and/or poor material quality, I have a car with less than 100,000 miles that has completely rusted thru the subframe. I was told by a Mercedes Benz dealer that this is a common problem with this car. The cost of repair was quoted at $4000. This was only discovered due to the MB mechanic removing the covers on on the subframe discovering the rust. I was told it would not pass inspection but it just did in February at the dealer I bought the car from. I told the MB dealer this and they said they probably didnt know the covers need removed to see the issue. This is a huge safety issue that people who drive these cars are probably not aware of. Failure of this area could cause loss of control as this is a critical suspension link responsible for maintaining steering direction of the rear wheels. Once these linkages fail the driver will lose control of the car. MB needs to held accountable for this design flaw and get the cars recalled. I do not have $4000 just lying around to make this repair and will be forced to continue to drive this car.

While traveling on the interstate @ 60 MPH, I loud knock was heard in the right rear. When brakes were applied, the vehicle pulled to the left, severely. Vehicle was taken to a mechanic on this date after making an appointment. Photos included show the issue as to why this occurred. The 'cradle' of the rear suspension on both, the left and right sides were completely rusted through. The vehicle is a 2011 Mercedes-Benz C-300, with 63,000 miles. After researching this on line, it appears this is an on-going issue with this year along with other years. This, is huge safety issue and the results could be catastrophic to the occupants and or other operators.

Rear subframe failure of left lower control arm mount bracket at weld that rusts prematurely from improper treatment at time of manufacturing After failure while braking at low speed 10mph rear end of vehicle fish tails left and front end of vehicle moves right There are numerous reports around the world with this specific model and identical safety hazard on the left side of vehicle in almost all cases Mercedes Benz refuses to acknowledge a defect in craftsmanship of the specified part and in many cases offer a $1000 credit towards a new vehicle As 1 of millions of Americans that owns this vehicle in question I believe it is necessary that the NHTSA steps in to assist with this issue as millions of American lives are at risk even if they do not own or operate this vehicle